Balboa-water-group Magna'flow Manifold Jet Manuel d'utilisateur télécharger pdf

MAGNA’FLOW MANIFOLD JET INSTRUCTIONS

The correct hole size for the Magna’ﬂow Manifold jet is 2 5/8”.

Before drilling the hole(s) to install the jet(s), make sure mounting surface is ﬂat. This will help assure the best seal. 1.

Drill one 2 5/8” hole for each jet. 2.

The gasket (#2) can be placed on the inside or outside surface. Make sure surface is smooth enough to seal. 3.

Before inserting the wall ﬁtting (#3) thru the hole, apply silicone to threaded area of wall ﬁtting only. This will help 4.

seal the wall ﬁtting (#3) and jet (#1) together.

Tighten wall ﬁtting (#3) into jet (#1) hand tight (10 FOOT POUNDS MAX ALLOWED) with gasket (#2) in place. The 5.

gasket (#2) and silicone will create a good seal.

After the jets are installed on spa, connect the plumbing. Be sure air line is connected to barb and water line is 6.

placed in socket. Use care when applying cement inside slip socket of the jets. If too much cement is used, it

may be pushed up inside jet housing causing poor jet performance.

Be sure air lines do not sag. If air lines sag, the jets may not aerate properly. 7.

Run spa for ﬁfteen minutes to clear debris from water lines, then thread nozzle assembly (#4) into place using a 8.

9/16” nut driver. Make sure nozzle assembly is threaded snugly into place.

Slip adjustment handle (#5) through wall ﬁtting (#3) lining up ribs on side of nozzle assembly (#4) with cut-outs at 9.

base of adjustment handle (#5). Press adjustment handle (#5) ﬁrmly into place. Clips must snap into place.

Insert therapy option into adjustment handle (#5). Pressing ﬁrmly to snap into place. To remove, pull on snout of 10.

eyeball (or ﬂowpath spout).

Note: It may be easier to remove therapy option with pump running. Block outlet

with index ﬁnger and pull on snout of eyeball or ﬂowpath spout.

Rotate adjustment handle (#5) 9011. ° to control ﬂow of water.

CAUTION: DO NOT APPLY ANY SILICONE INSIDE THE JET. THIS WILL INTERFERE WITH

THE OPERATION OF THE JET.

88-4876, Rev. A June 1, 2009

#1 3/4” x 3/8” MANIFOLD

JET BODY 10-4570

#2 AFII GASKET 10-5847

#3 WALL FITTING 10-4801

#4 NOZZLE ASSEMBLY 10-4804

#5 ADJUSTMENT HANDLE 10-4802

OR SL ADJUSTMENT HANDLE 10-4702

#6 DUAL PORT PATHFLOW 10-4820

#7 EYEBALL 10-4503

#8 CAGE 10-4806

#9 SINGLE PORT PATHFLOW 16-4821

° to control ﬂow of water 1

Résumé du contenu

Page 1 - ° to control ﬂow of water

MAGNA’FLOW MANIFOLD JET INSTRUCTIONS The correct hole size for the Magna’ﬂow Manifold jet is 2 5/8”. Before drilling the hole(s) to install the jet(s)

Commentaires sur ces manuels

Pas de commentaire

Balboa-water-group Magna'flow Manifold Jet Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau Balboa-water-group Magna'flow Manifold Jet. Balboa Water Group Magna'flow Manifold Jet User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour l'eau Balboa-water-group Magna'flow Manifold Jet