Balboa-water-group Servicing Slimline Air Control 10-2310 One Inch 10 Manuel d'utilisateur télécharger pdf (Page 1)

88-4040 Rev C June 30, 2009

TO DISASSEMBLE:

Align window on the handle (#7) with the 1.

“MIN” position. Place the palm of the hand

against the top of the Slimline Air Control

handle (#7), and press down ﬁrmly, rotating

the handle counterclockwise about a

quarter turn.

Grasp the outer edges of the Handle with 2.

your ﬁngertips and pull the Handle away from

the tub. The Slimline Air Control Handle/

Stem Assembly (#8) should come out freely

from the Outer Body (#3).

At this point, the entire Air Stem Assembly 3.

(#8) may be replaced. If further disassembly is

needed, go to the next step.

Once the Air Stem Assembly is removed, 4.

locate the rectangular slots on the Inner Body

(#5) and place your thumb and index ﬁngers

90° to the slot on the opposite sides. Your

ﬁngers should be against the underside of

the Handle (# 7).

In a pinching motion, squeeze the top of 5.

the Inner Body (# 5). With your thumb and

index ﬁngers still in place, pull the Inner

Body (#7) away from the Handle Assembly.

Squeezing ﬁrmly should release the latches

on the Inner Body to free it from the Handle

Assembly (#7).

Once the Inner Body is detached, the Seal 6.

(#6) can be removed from the inside of the

Inner Body and all pieces may be serviced.

TO REASSEMBLE:

Make sure handle/stem assembly (#8) is 1.

in the fully closed position by aligning the

window on the inner body (#5) and making

sure the foam is not showing. Insert handle/

stem assembly (#8) into outer body (#3)

with the window on the handle (#7) in the

“MAX” position.

Once the handle/stem assembly (#8) is in the 2.

outer body (#3), press on the top surface of

the handle (#7) ﬁrmly, and rotate the handle

clockwise until it stops (approx. 1/4 turn).

NOTE: IF RE-LUBRICATION IS NECESSARY,

USE ONLY A SILICONE BASED LUBRICANT!

DO NOT USE ANY TYPE OF PETROLEUM

BASED LUBRICANTS ... THEY WILL CAUSE

PRODUCT FAILURE.

Check the MAX and MIN position through 3.

the window on the top of the handle, and

match with the operation of the jets. If

aeration occurs in the “MIN” position, the

Slimline Air Control has been improperly

assembled. To correct, press down ﬁrmly

on the handle and rotate again clockwise.

Recheck the “MAX/MIN” position with the

operation of the jets.

SERVICING OF THE SLIMLINE AIR CONTROL

P/N 10-2310 1” SLIMLINE AIR CONTROL

P/N 10-2510 1/2” SLIMLINE AIR CONTROL

PART # FOR

10-2310

PART # FOR

10-2510 DESCRIPTION

1 10-3706 10-2205 NUT

2 10-3705 10-2204 GASKET

3 30-2316 30-2516 SLIMLINE OUTER BODY

4 30-2315 30-2515 SLIMLINE CHECK VALVE BALL

5 30-2313 30-2513 SLIMLINE INNER BODY

6 30-2314 30-2514 SEAL

7 30-2311 30-2517 SLIMLINE HANDLE W/ROTOR

8 10-2319 10-2519 SLIM LINE STEM ASSEMBLY

TO DISASSEMBLE: 1
TO REASSEMBLE: 1

Résumé du contenu

Page 1 - TO REASSEMBLE:

88-4040 Rev C June 30, 2009TO DISASSEMBLE: Align window on the handle (#7) with the 1. “MIN” position. Place the palm of the hand against the top o

Commentaires sur ces manuels

Pas de commentaire

Balboa-water-group Servicing Slimline Air Control 10-2310 One Inch 10 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau Balboa-water-group Servicing Slimline Air Control 10-2310 One Inch 10. Balboa Water Group Servicing Slimline Air Control 10-2310 One Inch 10-2510 One Half Inch User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Balboa-water-group Servicing Slimline Air Control 10-2310 One Inch 10 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour l'eau Balboa-water-group Servicing Slimline Air Control 10-2310 One Inch 10. Balboa Water Group Servicing Slimline Air Control 10-2310 One Inch 10-2510 One Half Inch User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour l'eau Balboa-water-group Servicing Slimline Air Control 10-2310 One Inch 10