Balboa-water-group ML700 - Mach 3 User Guide Manuel d'utilisateur télécharger pdf (Page 5)

Jets 2 (optional on some systems)

Press the “Jets 2” button once to turn pump 2 on or

off, and to shift between low and high speeds if it is

a two-speed pump. If left running, the pump will turn

off after a timeout period.

Blower

1-speed operation: on/off;

2-speed operation: med/hi/off; or

3-speed operation: lo/med/hi/off.

If left on, the blower will automatically turn off after a

timeout period.

Note: If your system does not have a “Blower” button, and

is labeled as ”Jets 3” instead, please see page 9 “Jets 3”.

Invert

Press the “Warm” or “Cool” button, then “Blower” to

change the numbers in the display to read upside down.

Repeat sequence to return the display to its normal

right-side-up display.

Note: If your system does not have a “Blower” button, use

”Jets 3” instead.

Preset Filter Cycles

On all systems, the pump and the ozone generator will

run during filtration. At the start of each filter cycle, the

blower will run briefly on its highest speed to purge the

air channels. The lowest speed of any other pumps and

the mister will also run briefly. On some circ systems,

pump 1 may also run for the duration of the filter.

(The following is specific to all systems that are

programmed according time)

There are two filter cycles per day. The start/end

times of each cycle are programmable. To program,

set time as instructed above, then press “Mode/Prog”

to advance to the next setting (or to exit after the last

setting). Default filter cycles can vary from system to

system. A common default is 8:00 AM to 10:00 AM and

8:00 PM to 10:00 PM. Press “Time” then “Mode/Prog”

to step through the filter settings to see how they are

currently set.

Each filter cycle automatically operates the pump for the

duration of the filter cycle. The filter 1 “

” icon will

light when filter 1 is running. The filter 2 “

” icon

will light when filter 2 is running.

(The following is specific to EL2000 and EL1000

systems that are programmed according to

duration rather than time)

The first filter cycle (“day”) begins 6 minutes after the

spa is powered up. The second filter cycle (“night”)

begins 12 hours later. Filter duration is programmable for

1-12 hours (

“

”-“ ”). The default filter duration can

vary from system to system. To program, press “Warm”

or “Cool,” then “Jets 1.” Press “Warm” or “Cool” to select

the filter duration. Press “Jets 1” to select the number

of filter cycles. The display will show “

” (both “day”

and “night” cycles); “

” (day cycle only); or “ ” (“night”

cycle only). Press “Warm” or “Cool” to adjust, then press

“Jets 1” to exit the programming mode. For continuous

filtration, use “

” and “ ”.

Note: EL1000 and some EL2000 systems are capable of

being programmed by time rather than by duration (see

Preset Filter Cycles section). On EL2000 and EL1000

systems with duration programming only, the spa powers

up at 12:54, thus the first filter cycles begins 6 minutes

later at 1:00. If you would like your spa to begin filtering

at another time, you may change the clock to align with

your preferred filter time, rather than the actual time

of day.

Optional Filter Cycle Programming

You are not required to set filter cycles; however, it

is an option available to you. To change the filter

cycle settings:

Press “Time” “Mode/Prog” “Mode/Prog” “Mode/Prog”

within 3 seconds. You will see the “PROGRAM,”

“FILTER 1” and “START TIME” icons appear on

the display.

Press “Warm” or “Cool” to choose the filter start

time hour. Enter the hour by pressing “Mode/Prog”.

Press “Warm” or “Cool” to choose the filter start

time minutes. Each press changes the start time by

5minutes.

Enter the minutes by pressing “Mode/Prog.”

Press “Mode/Prog” to see the “PROGRAM,” “FILTER 1”

and “END TIME” icons. Adjust the time as

done above.

Press “Mode/Prog” to see the “PROGRAM,” “FILTER 2”

and “START TIME” icons. Proceed as above.

Press “Mode/Prog” to see “PROGRAM,” “FILTER 2” and

“END TIME” icons. Adjust the time as done above.

Pressing “Mode/Prog” will enter the new filter cycle

times into the system and display the current water

temperature.

Pressing “Time” at any time during this programming

sequence will save the values entered up to that point

and exit programming.

If you would like to select continuous filtration, set the

filter 1 start and end times to be the exact same time.

In this case, the filter 2 start time only controls when

the second purge happens. Filter 2 end time will

be unavailable.

Page 3

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Balboa-water-group ML700 - Mach 3 User Guide Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Panneau de contrôle Balboa-water-group ML700 - Mach 3 User Guide